You press the power button and nothing happens. No fans, no lights, no beep. Before you pay for a diagnostic fee or a replacement, know this: many “dead” computers are fixed by one of the simple checks below.
I work through this same order whenever someone hands me a PC that “won’t turn on.” It’s the approach CompTIA A+ trains you to use, which I cover in 5 Things CompTIA A+ Taught Me About Home PC Troubleshooting: start with the cheapest, most likely cause and work toward the expensive ones. Change one thing at a time.
Safety first: Shut the PC down, switch off the power supply, and unplug it before opening the case. Touch bare metal on the case to discharge static before handling parts. An anti-static wrist strap makes this easier and is worth keeping in your toolbox.
Check 1: Confirm the Power Source Works
This is the most common cause.
- Is the power cable firmly seated at both the wall and the back of the PC?
- Is the surge protector or power strip switched on? Plug a lamp into the same outlet to test it.
- Try a different wall outlet, bypassing the strip.
- If you can, swap in a different power cable.
Check 2: Flip the Power Supply Switch
On the back of a desktop there’s a small rocker switch on the power supply (marked I and O). It gets bumped during cleaning or cable changes. Make sure it’s on the I side. If your unit has a voltage selector, confirm it’s set to 115V for the US.
Check 3: Disconnect Everything Except the Essentials
A faulty USB device, a short in a front-panel cable, or a bad peripheral can stop a PC from starting. Unplug everything except the power cable, monitor, keyboard, and mouse. Try the power button. If it starts, plug devices back in one at a time until the culprit shows itself.
Check 4: Drain the Residual Power
- Unplug the PC (or switch the PSU off).
- Hold the power button for 15 to 30 seconds to drain leftover charge.
- Plug back in, switch the PSU on, and try again.
On a laptop, also remove the battery if it’s removable, hold the power button, then reconnect the charger only.
Check 5: Is It Dead, or Just Not Displaying?
Many “won’t turn on” cases are really “turns on but shows nothing.” Look and listen:
- Do the case fans spin, or do any LEDs light up?
- Do you hear beep codes? Your motherboard manual lists what each pattern means.
- Is the monitor on the right input and connected to the graphics card (not the motherboard port) if you have a dedicated GPU?
- Try a different cable or monitor.
If the fans spin and lights come on, your power supply is working. The problem is further down the chain, which is often cheaper to fix.
Check 6: Reseat the RAM and Graphics Card
With the PC unplugged and static discharged:
- Remove each RAM stick and reinsert it firmly until both clips click.
- With two or more sticks, try one stick at a time, in different slots.
- Reseat the graphics card and check its power cables.
- Check that the 24-pin motherboard connector and CPU power connector are fully seated.
While the case is open, look for bulging capacitors, burn marks, or a burning smell. Any of those point to hardware failure. Dust buildup is worth clearing at this point too; a can of compressed air such as Dust-Off works well. For more on spotting trouble early, see 5 Warning Signs Your PC Is About to Fail.
A small precision screwdriver set is also handy here, since case screws, drive screws and motherboard standoffs often need different bits.
Check 7: Test the Power Supply
If nothing responds at all, the power supply is the most likely failure.
- Swap test: Borrow a known-good power supply of enough wattage. This is the most reliable method.
- PSU tester: A basic tester shows whether the main voltages are in range.
- Paperclip test: It only proves the fan can spin, not that voltages are stable under load. Don’t rely on it.
A power supply is one of the cheapest parts to replace. Buy a reputable brand rather than the cheapest unit.
When to Pay a Repairer
If all seven checks fail, the problem is likely worth professional help:
- A failed motherboard or CPU
- A laptop with a damaged DC jack or internal board
- Liquid damage
- A PC holding data you can’t afford to lose
You’ll also be a better customer. “I’ve tested the outlet, the PSU switch, reseated the RAM, and tried a second power supply” saves the technician time. If data is the priority, ask about copying files off the drive first.
After You’re Back Up and Running
Once the PC boots, check its condition so you aren’t surprised again. Our guide to the best free PC health check tools is a good next step, and backing up your PC protects your files either way. If it boots but runs poorly, work through the slow Windows PC checklist. If it starts and then crashes with a blue screen, read Windows Blue Screen (BSOD) Explained. For backups, I use the Seagate Portable 4TB (I own two).
Keep a Reference Handy
For a printable, step-by-step version of this kind of thinking, the Windows PC Troubleshooting Checklist puts the most common fixes in order on one reference you can keep next to your PC. To get new guides like this in your inbox, join the email list.
Want to learn more? If any of this sounds familiar — if you grew up somewhere analog (mechanical age) and ended up somewhere digital OR if you just enjoy anything Tech related or Electronics in general — you’re in the right place. Come join the conversation in the Hooked On Gaming | Programming or DC Global Bots, Gaming & Trading Discords. You can also check out our YouTube Channel where I share videos of creators that I like and will begin to share videos of my own; Sly’s Analog and Digital Chronicles. I’d love to hear your story too.
Some links in this post may be affiliate links. If you purchase through them, I may earn a small commission at no extra cost to you. (paid link)