If your PC turns on but there is no display, start with the cables and the monitor input, then reseat the RAM and graphics card, then try the motherboard video port and a BIOS reset. Most black-screen cases are one of those. The fans spin and the lights come on, so the power supply is doing its job. The picture just isn’t reaching the screen.
I go in the same order every time: cheapest and most likely first, one change at a time. If your PC shows no signs of life at all (no fans, no lights), start with PC Won’t Turn On? 7 Checks Before You Pay a Repairer instead.
Safety first: Before opening the case, shut down, switch off the power supply, unplug the PC, and touch bare metal on the case to discharge static. If you want to know why that matters, read ESD: Why Static Electricity Can Kill Your PC.
Check 1: The Monitor and Its Cable
Rule out the screen before you touch the PC.
- Is the monitor powered on, with its light showing?
- Press the monitor’s input button and cycle through HDMI, DisplayPort, and DVI. A monitor on the wrong input says “No Signal” even when the PC is fine.
- Unplug the video cable at both ends and plug it back in firmly.
- Try a different cable, or a different monitor or TV.
If a second screen works, the first monitor or cable was the problem.
Check 2: Plug Into the Right Port
This one catches a lot of people. If your PC has a dedicated graphics card (GPU), the monitor cable goes into the card, at the back of the case, usually lower down. The ports up near the USB ports belong to the motherboard and are often dead when a graphics card is installed.
After a build, upgrade, or cleaning, check that the cable didn’t get moved to the wrong spot.
Check 3: Try the Motherboard (iGPU) Port
Many processors have built-in graphics, called an integrated GPU or iGPU. This gives you a good way to test the graphics card:
- Shut down and unplug the PC.
- Move the monitor cable from the graphics card to the motherboard video port.
- Power on.
If you get a picture, your processor and motherboard are fine and the graphics card is the suspect. Reseat it (Check 5) or test it in another PC. If you get nothing, keep going. Not every processor has built-in graphics, so check your CPU’s specs. If the port does nothing at all, that may be why.
Check 4: Reseat the RAM
Loose or poorly seated memory is one of the most common causes of a black screen on a PC that is otherwise running.
- Unplug the PC and discharge static.
- Press the clips on each side of a stick and pull it out.
- Push it back in firmly until both clips click.
- With two or more sticks, try one stick at a time, in the slot your motherboard manual recommends. A bad stick or slot shows up fast this way.
New to memory? RAM Explained: How Much Do You Actually Need in 2026? covers the basics.
Check 5: Reseat the Graphics Card
- Release the latch at the end of the PCIe slot and lift the card out.
- Look at the gold contacts for dust or discoloration.
- Reinsert it until it clicks fully into the slot, and screw it to the case.
- Check that the PCIe power cables are firmly plugged into the card. Many cards need one or two of them.
While the case is open, check the 24-pin motherboard connector and the CPU power connector, and clear dust with compressed air.
Check 6: Listen for Beep Codes and Look for Lights
Many motherboards beep or show small status lights (often labeled CPU, DRAM, VGA, BOOT) when something fails. A light stuck on DRAM points to memory. One stuck on VGA points to graphics. Your motherboard manual lists what each pattern means, so look it up before you guess.
Check 7: Clear the CMOS (BIOS Reset)
A bad BIOS setting, often after a RAM or CPU change, can stop the display from starting. Resetting it returns the settings to defaults.
- Unplug the PC and switch off the power supply.
- Find the round, coin-style battery on the motherboard.
- Remove it, wait about a minute, and put it back. Some boards also have a CLR_CMOS jumper or button, so check the manual.
- Plug in and power on.
You may need to re-enter the date and a few settings afterward. Not sure what the BIOS does? Read What Is a BIOS (and Why Should You Care)?.
What the Results Tell You
- Picture on the motherboard port, none on the GPU: graphics card or its power cable.
- No picture anywhere, one RAM stick works: the other stick or slot is bad.
- Nothing works, beeps or red lights remain: likely a motherboard or CPU problem, which is when a repairer makes sense.
- Picture returns after CMOS reset: a BIOS setting was the cause. Don’t overclock again until you know why.
If you do need a repairer, tell them what you tried. It saves them time and you money.
Once You Have a Picture Again
Check the PC’s condition with the best free PC health check tools, and back up your PC so a future scare costs you nothing. To get new guides like this in your inbox, join the email list.
Want to learn more? If any of this sounds familiar — if you grew up somewhere analog (mechanical age) and ended up somewhere digital OR if you just enjoy anything Tech related or Electronics in general — you’re in the right place. Come join the conversation in the Hooked On Gaming | Programming or DC Global Bots, Gaming & Trading Discords. You can also check out our YouTube Channel where I share videos of creators that I like and will begin to share videos of my own; Sly’s Analog and Digital Chronicles. I’d love to hear your story too.